Qenker2-Player LED Arcade Game DIY Kit for USB MAME PC & Raspberry Pi - 2 Joysticks, 20 LED Buttons, 2 Zero Delay Encoders (Mixed Color)

Really good quality buttons, all leds works, the joystick feels sturdy and durableThe installation was straightforward its plug n playIt works for PC, automatically was recognized by steam and can map buttons to almost any game!Been playing street fighter V and bunch of other games for long hours and i had no issues at all!Overall, this diy kit is perfect for anyone looking to build or upgrade their arcade machine. It offers both functionality and aesthetics at an excellent price.

Well I ordered this pack, then decided on building a wall mount single player arcade so I didn’t use half of the buttons provided as it was a 2 player kit but the quality is great, the buttons have decent recoil and all of the LEDs worked. It was really easy to wire them up because most of the programming is done in Retropie and not off the control board provided

Works like a champ. I have zero complaints. Wired right up, but I would suggest plugging the controller into a portable charger so you can check the LEDs when you are wiring them. I had a couple errors on my part and needed to go trace back, I used the charger and made sure all my lights lit up and that also means you will wire your buttons correctly.Software immediately recognized the controllers and I was able to setup my buttons with ease.

Picture of product shows 3 pin harness with 0.110 Inch /2.8mm Terminals ending and buttons that have the same 0.110 Inch /2.8mm Terminals, 2 for ground, 1 for action, one for power. The buttons sent had 3 pin terminals and the wire harness had 3 pin terminals on both ends. I was unable to use this kit with the JAMMA harness in my arcade project. If you are looking for buttons that have the 0.110 Inch /2.8mm Terminals like those shown in the pictures and in the description rather than the 3 pin receptacle, do not buy this set. Quality of the buttons seemed OK but did not meet my expectations.

Bought this set for a full size arcade cabinet I'm building. All of the joysticks and buttons work perfectly with no light or press delay issues. Here are a few things I discovered and wanted to pass along.1. It would be nice if the connectors will a little longer. Fully extended they are 8" but once they are bent to attach to the connection points, you have maybe 6.5" of taunt distance. That means all of your buttons must be with 6" of the controller for that player. That made it difficult to put the 1/2 player start buttons where I really wanted them.2. The +/- was switched (opposite of indicators on button) on one button for the controller connection. No big deal. Switch them and it's fine.3. The +/- was switched (opposite of indicators on button) on one different button for the led light connection. No big deal. Switch them and it's fine.4. The specifications say the joysticks are 8 way and to buy different plates if you want 4/8 way switchable option. However, the plates that came with mine were already 4/8 way switchable. Just take the clear platic plate off the joystick, gently push up on the center and rotate it 45 degrees into a diamond instead of a square. Now it's a 4 way! This was a bonus.5. When measuring your hole distances, don't just make sure they are spaced enough for the button size on top but also for the nut that holds them in place underneath. Those are a little wider than the top button border so if there's not enough space between, you will have difficulty getting that nut on underneath.6. I wish it came with screws to mount the joysticks and control boards. Not that big of a deal but the holes on the control boards are quite small so appropriate screws would have been helpful. I didn't have any with a narrow enough body but big enough head so I ended up just using velcro on the bottom.Hope this helps someone!EDIT: After being in use for 2 weeks, the light goes off on one of the buttons when pressed. Must be a short inside the button that makes contact when pressed. That's enough, in addition to the other minor items, for me to take away a star now.

Looks great in the arcade 1 up and love the LED look. Buttons and joysticks are an upgrade from the stock for sure and work about 8/10 for fighting games in my opinion. One button is a little laggy but for a complete kit for $40 I can’t complain too much as it’s better then the stock buttons and sticks. Used extras on golden tee with a 5w adapter for a simple mod

Works great and feels premium compared to the stock buttons in Arcade1Up, also the PCB works with PS3 because the PS3 accepts USB controllers, the only complaint I have is Windows 10 not recognizing it in certain Microsoft Store games since it shows as a generic game controller, other than this I would highly recommend

Botonea de buena calidad