NZXT Vertical GPU Mounting Kit - AB-RH175-B1-175 mm PCIe 4.0x16 Riser Cable - GPU Holder - Sturdy Steel Bracket - Black

Used to mount a Gigabyte Aorus 4070 Ti Super Master (just rolls right off the tongue). It’s not a small GPU, nor lightweight. Installed in an H9 Elite March 2024. Absolutely no sag or problems with the riser adapter included. Pricey, but it reliably does the job.

Fits perfect in H9 Flow. Vertical setup looks great, card runs a bit warmer than horizontally. My 9070xt pci-e 5.0 continues to run in 5.0 although the spec on the cable states 4.0 with this vertical setup. Bought on sale for $56.

I bought this one for the obvious reason (vertically mounting my GPU). I went with NZXT as they make solid kit. I was not disappointed. While some might say that a vertical GPU bracket is super simple so what's the big deal? Well, I have used some sub-standard vertical GPU brackets over the years so having one that is dead on the money make a very big deal when you are both building and upgrading your rig. Simple but elegant, functional but solid, I am well pleased with this NZXT Vertical GPU mounting kit. Add to that the fact that the riser cable is PCIe 4.0 and you are good to go straight out of the box.

I am using this in an NZXT H5 Elite with a PowerColor Red Devil 7900 XTX. The card is THICC, but less so than any 4090 and many 4080s. I did buy the enhancement plate for the card, but it made it too wide and would not fit with it installed. Installation was relatively easy and went smoothly. Fit, finish, and function are very good and overall I am quite happy with the build.

Was annoying to set up. But once it’s installed. Wow does it look good. Take ur time installing the screws and make sure not to over tighten. I would recommend buying or using any stand to properly hold up the gpu. Nzxt gives, with the vertical mount a separate gpu stand. but i couldn’t figure out how to install it. Dope build though . little pricey, hoping that translate to better quality

This might cost as much as the H5 Flow but it has a premium quality feel to it and the PCIE 4.0 Riser has been stable in all the games I've tried. Old and AAA games.Surprisingly it's cooling about 7-8 degrees cooler in high demanding games. In the H5 Flow in horizontal position if you're using a big cooler that's on a 4080 Super or 4090 the fans don't have much room to breathe because in the H5 Flow the bottom side of case is covering the PSU at the bottom so it's just suffering from getting any room of air. With the vertical mount it provides more airflow and airflow orientation within the case is improved since now the GPU heatsink fins are pointed upwards towards the exhaust so you don't have hot air recirculating through the case.It's a tight fit with the Gigabyte 4080 Super Gaming OC. The only larger GPU's that won't fit are the Gigabyte Aorus Master and Asus ROG Strix 4080's and 4090's. And the benefit from the vertical mounting these huge GPU's gets rid of the known GPU sagging. There are other vertical brands but if you to be 100% sure it fits and supports your NZXT case stick with the NZXT vertical mounting kit. And the PCIE 4.0 is stable 100% in my experience.

It is very sturdy and works like a charm. I had signal issues with a previous PCIe Riser, but this one works perfectly. It is a bit on the expensive side, but I love the NZXT aestethic and quality so it is worth it for me. Be aware, if you are using it on cases other than the advertised H7 Line, it will fit, however some mods will have to be done to the back side of the case for the ports to be reachable. I had to bend the slot frames with a plier in order to connect the HMDI Cable. Does look a bit ugly, but it is an area that is rarely seen so it doesn't bother me too much. I've seen other people cut them all togeher too, which is a more visually pleasing mod.

I ordered these on Amazon because they were a bit cheaper than NZXTs website. It worked great and was easy to install with the GPU.