iCrimp PEX Clamp Tool Kit for 3/8-in, 1/2-in, 3/4-in, 1-in PEX Clamp Cinch & Removal, c/w 1/2''(20 Pack) and 3/4''(10 Pack) PEX Clamp Rings, PEX Tubing Cutter

Here is the scenario. I was adding a water spigot onto our upper deck for watering our porch plants. The closest water source was the kitchen sink, which was problematic and time consuming to go in and out of the house for more water. So, I was going to tap into the 3/4" pex water line that went under the deck to an outside faucet . . . but as you can see from the second pic, it is pretty tight in there. I cut the line, and was able to pull one end out to install one side of the Tee. I had already pre-clamped the tubing to the side of the Tee going up to the new faucet. And I was able to pull the tubing out to clamp the 2nd "through" end of the Tee . . . . but no matter how much I contorted my body/hands, I could not get the crimper in to fasten the last ring clamp. The handles just opened too wide for the available space. I finally gave up and ordered this "one handed" ratcheting Pex crimping tool . . . . Viola! It fit right in, and the clamp was finally installed! Not only that, but I believe it will become my "go to" crimper for most of my other crimping needs! Excellent tool, and I highly recommend it!

Oh man these things saved my bacon. I've been replacing cinch clamps used on a new rv to attach flexible braided line to pex fittings and will leak. Most of these are in tight spots and impossible to crimp with my standard crimper that need two hands and lots of space to open the jaws. I replaced one underneath my rv shower floor through a tiny access panel that I could only get one hand into. I wish they made a ratcheting cinch clamp cutter in this same style, would be a great kit! These crimp very tightly and release when proper tension has been reached. There is no bypass release lever, so once you start to cinch a clamp, you are committed until it is fully crimped.

Works great on my 3/4" PEX B plumbing. Nice that that the set came with 1/2" and 3/4" SS clamps. First time using this method of piping. The clamp tool does need to be pressed into the fitting a bit so that it does slip off, but I suspect this is true of any brand of tool based on the clamp design.I'm pretty picky about quality and I was completely satisfied with the materials and build of the tools. The cutter seems a bit on the cheaper side, but it cut just fine and I don't see any weak points as far as construction. Both tools have a rubberized or vinyl coating on the handles and were easy enough to use for a first timer.

Well made and they appear to do the job well so far. I haven't yet tested for leaks however.

I picked up the iCrimp PC-PC02KIT PEX Clamp Crimping Tool Kit for a recent plumbing project, and it performed flawlessly. Here’s what stood out:All-Inclusive Kit: Comes with both ½″ (20 clamps) and ¾″ (10 clamps) rings, plus a sharp pipe cutter and a cinch/removal tool—everything you need in one case.Sturdy Crimping Tool: The ratcheting mechanism ensures a consistent, leak-proof seal every time, with minimal hand fatigue.Clean Cuts: The integrated PEX cutter slices cleanly through tubing without crushing or deforming the pipe.Easy Clamp Removal: The included removal tool makes rework simple, without damaging fittings—ideal for adjustments or repairs.Durable Build: Heavy-duty steel construction feels rock solid and should last through many jobs.Room for Improvement:None—I couldn’t find a single downside.If you need a reliable, professional-grade PEX crimping solution that “just works,” this iCrimp kit is exactly that. Highly recommended for both DIYers and pros

I purchased this Pex A crimping tool to replace the old PVC lines serving our new hot water heater with Pex. The crimping tool worked perfectly, although it took greater hand strength to operate than an expensive model. To be clear, it didn’t take excessive strength, just a bit more.The action on the crimper was smooth and it came out of the box correctly calibrated. If you ever need to recalibrate it, a go/no-go gauge is included and adjustment is made with a knurled screw.The included pipe cutter was a pleasant surprise and worked perfectly. It was a real labor savor when I was cutting pipe in a cramped crawl space. I also appreciated the selection of crimping rings that came in the kit.Don’t let the low price fool you. This is a high quality tool that worked perfectly!

so far so good. used once and worked like it should.

Shipped very quick. Looks like good quality I haven't used them yet.